M1A Scope Mount Comparison
Best M1a Scope Mount on April 2024 Shopping Deals at Bestonio.com
Airborne Scope Mount is 20 percent Lighter than our standard steel mount. Precision mil-spec picatinny rail and see-thru U-channel for iron sight use with scope/rings attached Rail hardened to 45-50 Rc for a tough and strong mounting platform. Produced from solid chrome-moly steel bar, not investment cast 5 degree case deflector angle milled on the... [Read More]
This sturdy aluminum mount provides a Picatinny-Style rail above the receiver of the M1A. The 4th generation mount features 3 points of contact with the receiver. Includes all mounting hardware and instruction.
The Aluminum Scope Mount weighs 4.3 oz (122.3 g) and is 5-7⁄16" (13.8cm) long, 1-3/4" (4.4cm) wide, 2-2/8" (6.03cm) high. Precision milled, using USA made 6061 heat-treat aerospace aluminum alloy and then put through a rigorous multiple point final inspection process to insure a quality fit and function prior to finishing with a black hard-coat a... [Read More]
M1SURPLUS Scope Mount Rail - Low Profile Design - Durable Aluminum Material - Anodized matte black finish - Fits most Springfield M1A Rifles - Does "NOT" fit M14 rifles - Installation will require filling and fitting procedures on the mount - Installation instructions included - Gunsmith Installation recommended
The Steel Scope Mount weighs 11.1 oz. (315.1 g) and is precision milled using USA made 4142 chrome-moly bar stock with a hardness of 28-32 RC. It is put through a rigorous multiple point final inspection process to insure a quality fit and function prior to finishing - with a manganese phosphate finish. Each mount comes with all mounting hardware, ... [Read More]
The GG&G maa Scout scope mount easily installs in the cut out of the upper factory hand guard. The overall design provides smooth integrated appearance. Specifically designed for the maa "Scout squad" or "so com 16", with cutout factory top hand guard.
Springfield 1 Piece Base Matte 4th Generation M1A MA5028. Note: Please check your state regulations, hunting regulations, etc before placing an order for any of our items. Your order may be canceled if the item is not able to be shipped to your state due to their regulations.
Since its introduction to the marketplace in 1989, this foundation has maintained its reputation as being the best mounting systems for the M21/14 Rifle. The A.R.M.S.® #18 offers interchangeability of Day & Night Vision, with an ultra low profile and the A.R.M.S., SWAN ® aka Mil-Std. 1913 Rail. Made of 8620 case hardened steel. Precision fit to t... [Read More]
The SADLAK M14/M1A Front Rail, Aluminum Low Profile Rail are our light weight and low cost option to the more robust steel rail. An internal nut plate is not used with these models. Dimensions are 3" Length x 3/4" Width x .5" Height. The Aluminum Rail is attached with two internal screws and special washers, while still retaining your stock sling s... [Read More]
This low-profile "See-Thru" Scope Mount is designed to fit Springfield .308 rifles like SOCOM 16, M14/M1A. Measuring over 6", its Picatinny/Weaver compatible top rail has a total of 15 slots. Mount screw with built-in washer included.
M1Surplus Optics Kit For Springfield M1A Rifles ! - ( SCOPE FEATURES ) One piece anodized aluminum main tube * Multi Coated Lenses * Four times Zoom Range * Quick Focus eyepiece * Reticles features an illumination function with multiple brightness setting to enhance target acquisition * Target style adjustment knobs with turret caps * Includes one ... [Read More]
The Monstrum Tactical S3932-R-RGAO is a full-featured scope suitable for hunting, target shooting, or tactical use. The scope comes equipped with: Adjustable 3-9 times magnification, for targeting out to 300 yards and beyond Adjustable reticle illumination with 5 brightness levels in both red and green, allowing for better reticle visibility at n... [Read More]
The Monstrum Tactical Offset Dual Ring Picatinny Scope Mount is built to mount standard 1 inch tube scopes to any standard Picatinny rail equipped rifle. The offset design provides an additional 2 inches of forward extension, allowing extra flexibility for optimum eye relief and shooting position. The mount is 5.75 inches in total length. The base ... [Read More]
Mount 1-inch telescopic sights onto flattop style rifles using the Vortex Cantilever 1-Inch Mount. This rail mount engineered by the geniuses at Vortex positions the center of the riflescope tube at a height of 1.59 inches (40.39 mm) from the base. The Vortex Cantilever 1-Inch Mount features a 2-inch offset that positions the scope in a forward loc... [Read More]
© Bestonio.com - all rights reserved - Sitemap Bestonio.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com