10 Best Vacuum Tube Amplifiers 2019
Best Chinese Tube Amp on April 2024 Shopping Deals at Bestonio.com
***IMPORTANT: 5654W tubes can ONLY be used to replace 7-pin 6J1, 6J1P / 6J1P-EB / 6Zh1P-EV, 6AK5, 6AK5W or EF95 tubes. If in doubt check with your amplifier manufacturer (or contact us) to verify that 5654W tubes can be used as a replacement in your particular audio device. AMPLIFIER DAMAGE CAN OCCUR IF YOU USE THE WRONG TYPE OF TUBE AS A REPLACEME... [Read More]
Input: Gold Plated Unbalanced (RCA) Jacks Output: 1/4" Gold Plated Stereo Headphone out Tube Options: 6JI standard Frequency Response: 10HZ ~ 50KHz (minus3 dB) THD plus N: 0.2 percent: 1Vrms @ 1000Hz 0.6 percent: 3Vrms @ 1000Hz 1.0 percent: 5Vrms @ 1000Hz Signal to Noise: 92dB Suitable Headphone Impedance: 8 ~ 600 ohms Input Impedance: 50K ohms Pow... [Read More]
This tube has a well balanced, colorful tone with strongly defined lows, mids and smooth highs. It allows for more clean head-room than higher gain 12AX7s. In overdrive, it is smooth and strong with well defined lows and Mids. When pushed into overdrive it offers clean distortion with well balanced lows and Mids. The jj 12AX7 is well suited for all... [Read More]
All tube guitar amplifier featuring 12AX7 preamp tube and EL84 power tube. Single end design for the purest tone. 5 Watts of pure class A power combine with 8" high output speaker is good for solitary practice or performing in a small club.
The Dayton Audio HTA20BT combines the efficiency and power of solid state class D amplifier topology with the warmth and character of a vacuum tube preamp section. The results are a delightfully articulate and natural sound that is sure to please even the most refined ears.
Parameters: With original and new tubes 6n9p+EL34B Input Impedance: 100Kohm Output Impedance:4ohm 8ohm Signal to Noise Ratio: 89dB Input Sensitivity: 500--2000mV Input :110V/ 220V Output power:13w+13w (RMS) Frequeney responses: 20Hz--30KHz+/-1dB Supply Votage: all voltages are available 60Hz/50Hz Total Hamonic Distortion: less than 1%(1KHz) Tubes ... [Read More]
Color:MC-13S Specification Output Power:40W + 40W (8ohm) Frequency Response:10Hz -- 60kHz (±2dB) Signal/Noise Ratio: ≥85dB (A) Load impedance: 8ohm or 4ohm Distortion:≤0.9%(28W) Maximum Power Consumption:220W Sensitivity:≤0.26V Tubes: 6CA7T x 4 12AX7B x 2 12AU7 x 2
Notice:Both 4Ω and 8Ω speakers can connect to the 8Ω and 0Ω posts of this amplifier. Specifications: Output power: 6.8W * 2 Frequency response: 20Hz-20KHz Input impedance: 100K ohms Output impedance: 4/8Ω SNR: 90db Input Sensitivity: 500mv-2000mv Harmonic distortion: 1% (1KHz) Tube: 5Z4P * 1 6H8C * 2 6P1 * 4 Operating voltage: 110V Weight: ab... [Read More]
Notice: As a phono preamp, it is suited for MM turntables only. Do not support MC turntables. As an AUX preamp, it is suited for devices like CD, DAC, PC, cellphone. Please note as a phono preamp, it can only work with MM turntables. Please note your turntable should have no built-in phono preamp. If it has, please make sure there is a PHONO OUT/... [Read More]
Performance: Using classical tube 6j1 design and optimize the route. Tube can be replaced design,soft voice. Patent power conversion module. The first vehicle with DC12V power supply only. All aluminum alloy shell,heavy gold PCB,gold-plated interface. Can match digital power amplifier analog power amplifier,active speakers. Technical: Power supply... [Read More]
Replaceable Tube Modules: Switch between 12 series or 6 series: ① 6 series available: 6DJ8/6922/6N11/E88CC/6H23... ② 12 series available: 12AU7/ECC8/5814/6189/B329/CV4003/ECC802S... Parameters: Working voltage: DC24V, 1.5A at least Input sensitivity: 50mV Gain: 32dB Audio input: 3.5mm audio jack & Stereo L/R RCA Audio output: 3.5mm headphone &... [Read More]
Troubleshooting: Please note that this product is a preamplifier. It is not an amplifier and needs to be connected with an amplifier or active audio devices. Also, it is not a phono preamp and can't work with a turntable. For noise issue: There is a large probability that the low-quality audio cable causes the static noise. Please make sure the ... [Read More]
The AC10 was one of the first amplifiers to bear the VOX name and was available only for a short period of time in the early 1960s. Long adored for his ability to achieve rich, articulate tube tone at very manageable volumes, the AC10 has become a highly coveted piece of VOX history since it's discontinuation in 1965. Now in 2015, VOX is proud to r... [Read More]
METEOR 20 WATT TUBE STAGE DRIVEN HEAD In their new banTamP series of Heads The Meteor is just one awesome little powder keg in their new banTamP series, and will be offering more models soon. 20 watts of tone in easy take anywhere configuration. The Meteor from Joyos BantamP series is a very compact and portable 20 Watt head. It gives you a modern ... [Read More]
TIPS:when you got the package. you need assemble the preamp board into blue box by youself. it's easy. then you can use it. (the list picture is assembled. just for refer.) Assembled finish PCB. both panel not yet. when you get it.you need assemble it by yourself, easy work. after you can using it. It's a very cool preamp.it's newest version. 1,PCB... [Read More]
P20 is Loxjie's first full balance tube amplifier headphone power amplifier!It use the military grade 6N3 tube,Plus the well-designed and calibrated amplifier circuit! Let the amplifier have lower distortion under the premise of ensuring"Tube Style"!And the P20 also has true balanced inputs and outputs!This can maximize the performance of the headp... [Read More]
© Bestonio.com - all rights reserved - Sitemap Bestonio.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com