Bluetooth 2.0 VS Bluetooth 4.0 (BLE) || Is an Upgrade worth it?
Best Bluetooth Module For Arduino on April 2024 Shopping Deals at Bestonio.com
We strive to put our hundred percent to resolve your issues and try our best to achieve your satisfaction!About Feedback:Our company pays great attentions to the shopping experiences and feedback from the customers.Your satisfaction and positive feedback with 5 stars is the motivation for us to move forward.It would be highly appreciated if you cou... [Read More]
Module parameters: 1.PCB Size: 37.3mm (Long) *15.5mm (wide) 2. Weight: 3.5g 3. Input voltage: 3.6V--6V, prohibit exceeding 7V 4. Leads 6 feet: EN/VCC/GND/RXD/TXD/STATE (Bluetooth state leads, not connected output low level, the output high level after connection) 5. With the connection status indicator, LED flash indicates no Bluetooth connectio... [Read More]
The Core module is HC-05 bluetooth 2.0 module. By using this Bluetooth module, you can quickly add Bluetooth features to your arduino project. The factory setting is slave mode, but you can set this module to master mode so that you might be able to connect to other Bluetooth 2.0 devices. Please note: This is a classic Bluetooth 2.0 module, it is n... [Read More]
Note: This module does not support any iOS device (iPhone, iPad) Features: 1, Core module uses HC-06, leads from the module interface includes VCC, GND, TXD, RXD. 2, Led indicate Bluetooth connection status, Blinking indicates standby, and steady light indicates that a connection has been established. 3, the input voltage is 3.6 ~ 6V, current is a... [Read More]
This is a Bluetooth 4.0 module with 4pin base board that can support iphone4s or later. But does not support the version is lower than the android 4.3 phone(it don't support classic bluetooth 2.0 spp features) The core module is HM-10 Base board from DSD TECH Operating voltage: 3.3V to 6VAbout APP We provide a free app for this module for you to... [Read More]
Product Introduction: 1.Input voltage: 3.3V/5V only needs a set of power supply. 2.Built in level conversion function: 3.If you use MCU 5.0V and Bluetooth module communication, 5.0V power supply port, TX RX logic level 5V; 4.If you use MCU 3.3V and Bluetooth module communication, 3.3V power supply port, TX RX logic level 3.3V 5.RX, Bluetooth mo... [Read More]
The Core module is HC-06 Wireless bluetooth 2.0 serial module. By using this HC06 Bluetooth module , you can quickly add Bluetooth features to your arduino project or other wireless DIY Project. The factory setting is slave mode,default Baud Rate: 9600 , PIN: 1234 Please note: This is a classic Bluetooth 2.0 module for Aduino, it is not compatibl... [Read More]
How to use the hc 05 Bluetooth module for controlling Arduino via Bluetooth communication? We are here to help you implement all the projects above. Module parameters: 1.PCB Size: 37.3mm (Long) *15.5mm (wide) 2. Weight: 3.5g 3. Input voltage: 3.6V--6V, prohibit exceeding 7V 4. Leads 6 feet: EN/VCC/GND/RXD/TXD/STATE (Bluetooth state leads, not con... [Read More]
If you need to use iphone or ipad to control your arduino project, SH-M08 4.0 ble slave module with 6pin baseboard may be a good choice. Fully compatible with ios7.0 or later and iPhone 4s / 5 / 5s 6 / 6s or later Also compatible with Android 4.3 or later. Please note: if the version of the Android os is less than 4.3. it is not compatible. This m... [Read More]
If you need to use iphone or ipad to control your arduino project, sh-hc-08 4.0 ble slave module with 6pin baseboard may be a good choice. Fully compatible with ios7.0 or later and iPhone 4s / 5 / 5s 6 / 6s. Also compatible with Android 4.3 or later. Please note: if the version of the Android os is less than 4.3. it is not compatible. This module ... [Read More]
Aideepen HC-05 Bluetooth Module (Master/Slave) provides a wireless communication link between your Arduino and any bluetooth capable device Specification: Working voltage: 3.3 V Working current: matching for 30mA, matching the communication for 8mA Wiring(only need 4 wires): RX to RXD / TX to TXD / GND to GND / 3.6V to 6V Package Included: 2 x HC... [Read More]
The BLE Board has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. The ATmega328P provide UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). An TI CC2540 chip on the board channels this serial communication over USB and the TI CC2540 chip drivers (incl... [Read More]
Bestgle HC-05 6 Pin Wireless Bluetooth RF Transceiver Module BT Serial Pass-Through Module for Arduino - Master and Slave 2-IN-1 HC 05 Wireless BT Module, you can connect to other Bluetooth 2.0 devices. - Adopt the CSR BC417 mainstream bluetooth chip, bluetooth V2.0 SPP protocol standards - Press the button, the module enter the AT mode, set param... [Read More]
The HM-19 is an upgraded version of the HM-11. The HM-19 uses TI's CC2640R2F chip as the master IC. Compared to HM-11, HM-19 is a Bluetooth 5.0 BLE module,it has a faster transfer rate and a larger MTU. This module can be used not only for DIY project, but also for your products. Work voltage(VCC): 3.6V to 6V TTL logic level (TX, RX): 3.3V Bl... [Read More]
Allows your device to both send or receive the TTL data via Bluetooth technology without connecting a serial cable to your computer. This bluetooth bluetooth is perfect for adding bluetooth functionality to your arduino project. But don't think that it is limited to just being used there. Another use you will find for this bluetooth module is with ... [Read More]
This is a Bluetooth 4.0 dual-mode module. Compatible with Bluetooth Smart (Bluetooth low energy) and Classic Bluetooth This also means that it can support both iphone and almost all of the android phone. Please note: When the module works in bluetooth 4.0 low energy mode. It only supports iphone4s or later. When the module works in the bluetooth cl... [Read More]
Default serail port setting : 9600 1 Pairing code : 1234 Current : Paring - 35mA, Connected - 8mA Temperature : -40~ +105 Degrees Celsius User defined Baud rate : 1200,2400,4800, 9600, 19200,38400,57600,115200,230400,460800,921600,1382400.
The Core module is HC-05 bluetooth 2.0 serial module. By using this HC 05 Bluetooth module , you can quickly add Bluetooth features to your arduino project or other wireless DIY Project. The factory setting is slave mode, but you can set this module to master mode so that you might be able to connect to other Bluetooth 2.0 devices. Please note: Th... [Read More]
User Manual: http://osoyoo.com/?p=18704Description:✔ Model: HC-02✔ Working frequency: 2.4G✔ Communication Interface: UA pin 3.3VTTL level✔ Input Voltage: 3.2 ~ 6V✔ Operating Voltage: 3.0 ~ 3.6V✔ RSSI Support: not support✔ Communication Level: 3.3V✔ Transmitted Power: 6dBm (max)✔ Reference Distance:10m✔ Air Data ... [Read More]
Bluetooth protocal : Bluetooth Specification v2.0+EDR Frequency : 2.4GHz ISM band Modulation : GFSK(Gaussian Frequency Shift Keying) Emission power : ≤4dBm, Class 2 Sensitivity : ≤-84dBm at 0.1% BE Speed : Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps Security : Authentication and encryption Profiles : Bluetooth serial p... [Read More]
© Bestonio.com - all rights reserved - Sitemap Bestonio.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com